Sealant Clay: 10 Ways to Fill Gaps, Pipe Openings and Wall Penetrations

Small holes, pipe openings and tight spaces do not always need tape or caulk. Here are 10 practical ways to use sealant clay, plus how to apply it.

Sealant clay pressed into the gap around a pipe opening in a wall

Not every gap needs a roll of tape or a tube of caulk. Some openings are small, awkward or hard to reach: the space around a pipe, a cable hole in a wall, the hole where a screw used to be. For those jobs, a moldable sealant clay is faster and cleaner than getting out a caulk gun.

ExtremeSeal™ Sealant Clay (6-Pack) molds by hand to fill small holes, gaps, pipe openings, wall penetrations and tight spaces. Each pack contains 20g (0.7 oz), sized for quick, targeted jobs. Here are 10 ways to put it to work.

What Is Sealant Clay, and When Should You Use It?

Sealant clay is a hand-moldable sealing product. You pinch off what you need, press it into the opening and shape it with your fingers. No special tools required.

It works best on small, irregular openings and in tight spots. For long seams, wide cracks and exposed roof joints, butyl tape is the better tool. A simple rule: tape for seams, clay for holes.

10 Ways to Use Sealant Clay

  1. Pipe openings under sinks. Fill the gap where supply and drain pipes pass through the cabinet wall.
  2. Wall penetrations for cables and wires. Close up the opening around TV, internet or power cables that run through a wall.
  3. AC line set and wall sleeve gaps. Fill the space where refrigerant or condensate lines enter the building.
  4. Outdoor faucet and hose bib gaps. Seal around the pipe where it goes through the exterior wall.
  5. RV, camper and trailer utility openings. Fill small gaps around lines, cables or pipes that pass through the body.
  6. Vent and duct edges. Close small gaps where a vent or duct meets the wall or ceiling opening.
  7. Holes from removed screws, anchors and hooks. Press a small piece in and smooth it flush.
  8. Window and door frame corners. Fill tight corner gaps that are awkward to reach with caulk.
  9. Garage, shed and workshop walls. Close up openings where wires, pipes or conduit pass through.
  10. Tight spaces behind appliances and in corners. Reach spots a caulk gun cannot, and shape the clay by hand.

For exposed outdoor spots, you can add a strip of butyl tape over the clay for extra protection.

Hand molding sealant clay with a thumb into a gap where a pipe passes through a wall

How to Apply Sealant Clay

  1. Clean the area. Remove dust, dirt and loose debris so the clay can grip the surface. If old adhesive is in the way, our guide on removing old tape residue can help.
  2. Take only what you need. Pinch off a piece sized for the opening. Each pack holds 20g, so plan one pack per small job.
  3. Press it in. Push the clay into the opening so it fills the gap rather than just covering the surface.
  4. Shape and smooth. Use your finger to work the edges flush with the surface and remove any excess.
  5. Check your work. Look around the edges for any remaining gaps and add a little more clay where needed.
Under-sink cabinet with pipe openings neatly sealed with sealant clay

Tips and Limits to Keep in Mind

  • Match the tool to the size. Sealant clay is meant for small holes and targeted jobs. Larger openings and structural damage need a proper repair.
  • It is not a fix for an active pipe leak. If water is escaping a pipe, see our guide to stopping a pipe leak with waterproof tape.
  • Mind building codes. Do not use it as a firestop where code requires a fire-rated product. Check your local requirements.
  • Keep spare packs. The 6-pack gives you six targeted jobs, which is handy for a few openings in one project.

Pair Clay with Tape for a Complete Seal

Many projects need both: clay for the holes and penetrations, and butyl tape for the seams and cracks around them. Extreme Tape™ comes in 2 in, 4 in and 6 in widths.

Shop ExtremeSeal™ Sealant Clay (6-Pack) →

Free shipping on orders $60+. 30-Day Money-Back Guarantee.

FAQ

How much comes in a pack? The set has 6 packs, and each pack contains 20g (0.7 oz).

What can I fill with it? It is made for small holes, gaps, pipe openings, wall penetrations and tight spaces.

Do I need any tools? No. The clay molds by hand.

Can I use it for large holes? It is designed for small, targeted jobs. For larger openings or structural damage, use a proper repair.

Can it stop a leaking pipe? It is not intended as a repair for active leaks. For a leaking pipe, shut off the water and use a suitable repair, and see our pipe leak guide for a temporary tape fix.

Can I use it as a firestop? No. Where building code calls for a fire-rated product, use one that carries that rating.

Back to blog